This is adapted from the FlightAware fork, with some cleanup and
modifications needed to work with the net-cleanup changes.
Inclusion of "verbatim" TSV data read from an AVR-format input
connection is not supported.
Pull #54 breaks the Windows version of dump1090 due to a bug in the
inet_aton() windows function.
1) Fix the bug in the windows inet_aton()
2) Modify the command line code to strdup() the command line string.
3) Leave the Modes.net_bind_address pointer NULL if no command line
specified
Pull #54 permits changing the default bind address. The default was
127.0.0.1. This prevents external access unless a command line switch is
used. Since many users of dump1090 are using dump1090 as remote receiver
heads for programs such as plane plotter, this is undesirable. If you
want to lock down your RPi for local use only then use the command line
switch. If not, retain legacy open mode by binding to 0.0.0.0 by
default.
Mostly refactoring the common code that was duplicated
between the different output types so that there aren't
many copies floating around.
This introduces "struct net_writer" to store the state of a
particular type of output service - buffers, time of last write,
connection count etc. prepareWrite() / completeWrite() give access
to the buffer and handle the actual writes and flushing when needed.
Heartbeat and time-based flushing move into a generic periodic-work
function.
Update the SBS output code to use the new infrastructure. This makes
a big different to CPU use when under load.
When we read from some client A, we may end up forwarding a message to other
clients. If we forward to some client B and there is a write error, then
we close B and remove it from the client list. However, if before this happened
A->next == B, then the read loop will still be holding on to a pointer to B,
and we crash.
As it's unpredictable what clients could be closed at what point, the simplest
approach is to retain closed clients in the list until we are at a point where
we know there are no stray pointers on stack, and only then modify the list.
This also simplifies anything that has to loop over clients, as it doesn't need
to worry about the current client being freed under it.
If we demodulate a message in 2.4MHz mode and it has a bad, uncorrectable CRC,
and --phase-enhance is on, then retry with the other possible phases until
we get a good CRC or run out of phases to try.
This is very expensive in AGC mode (lots of candidates that are not real
messages) but relatively cheap otherwise. It yields another 10% messages.
Also factor out some common stats code to avoid lots more copy/paste.
There is a danger in always using relative decoding where possible.
If there is an undetected error in the first pair of messages received,
then global CPR decoding will give a bad position, and subsequent
relative decoding will just walk around near that bad position even
though many error-free pairs of odd/even messages may have been received.
The first pair of position messages also tends to be the most error-prone, as
they are usually received at the extreme edge of receiver range.
(I see this happen at least once a day in practice)
So, instead, prefer to use global decoding when we have sufficiently recent data.
With recent data this should always be as good as relative decoding, and it
avoids getting stuck with bad data for long periods of time. If we don't have
enough recent data for a global solution, fall back to relative decoding.
This disables most decoding of the contents of Mode S messages, aircraft tracking, and some output modes that depend on them.
It's intended for edge receivers that just forward to a central hub rather than processing data locally.
Release of COAA PlanePlotter MLAT and SMU support for RPi
ppup1090 now supports Ground Stations functions required for MLAT and
SMU operation. This is *ONLY* available for RPi and similar linux
hardware.
Also included are sample startup scripts for dump1090 only and
dump1090+ppup1090 together.
A few minor additions and bug fixes as detailed below
1) Additional command line option "--net-buffer <n>" to specify the TCP
output buffer size. Default is n=0, which is 64Kb. Specify a value of n
to increase the buffer size according to Size = 64Kb * 2^n, so an n of
1 = 128Kb, n=2 is 256Kb etc. n is limited to 7, so the max size is 8Mb.
This option may assist if you have a high number of aircraft being
received, and an unreliable network connection, or if the receiving end
can be busy for an extended time.
2) Bug fix in ppup1090 which prevented the uploading of valid
ModeA/Squawk codes
3) Bug fix per Markus Grab's commit.
Make the modifications necessary to compile dump1090 for WinXP, Win7 and
hopefully Win8.
The files can be compiled using M$ Visual Studio/C++ 6.0. Due to various
licensing issues, I haven't included the libraries or DLLs. You will
need to locate pthreadVC2.lib and rtlsdr.lib to link the file, install
the zadig drivers to support the dongle, and locate libusb-1.0.dll,
msvcr100.dll, pthreadVC2.dll and rtlsdr.dll.
dump1090.exe will not run on any Windows version prior to XP SP2,
because msvcr100.dll imports several functions from the Windows kernel
that are not available on earlier versions. This means dump1090 won't
work on Win2K.
The major change to the code relates to file handles. The original code
assumes Linux behaviour in that handles are allocated from 0
sequentially upwards. However Windows handles are allocated pseudo
randomly, and handle numbers greater than 1024 would break the code. The
code has therefore been modified to use a linked list of connection
structures, rather than a static array limited to 1024 entries.
Some users have reported issues where the TCP link to dump1090 can be
lost at times of low traffic density - typically in the middle of the
night. One possible reason for this is that some routers drop the link
if there is no traffic for a predetermined period.
To try and resolve this, dump1090 now sends a 'null' packet consisting
of 7 "0x00" bytes approximately once a minute if there is no real
received traffic during this time. This packet should be discarded by
the application receiving the dump1090 because it will have an invalid
checksum, and ICAO address 0x000000 is also invalid. However, this null
packet should be enough to keep routers alive.
