Switch signalLevel back to a power measurement, don't put SNR in there.
But make it a 0.0 - 1.0 double so we're not scaling everywhere.
Adjust for the amplitude offset when calculating power.
Adapt everything else to the new scheme.
location (which may not be the aircraft location).
I suspect this sanity check is, in fact, redundant now that the
rest of the algorithm has had some bugs fixed; it should only
produce results within half a cell by definition.
Mostly refactoring the common code that was duplicated
between the different output types so that there aren't
many copies floating around.
This introduces "struct net_writer" to store the state of a
particular type of output service - buffers, time of last write,
connection count etc. prepareWrite() / completeWrite() give access
to the buffer and handle the actual writes and flushing when needed.
Heartbeat and time-based flushing move into a generic periodic-work
function.
Update the SBS output code to use the new infrastructure. This makes
a big different to CPU use when under load.
If we demodulate a message in 2.4MHz mode and it has a bad, uncorrectable CRC,
and --phase-enhance is on, then retry with the other possible phases until
we get a good CRC or run out of phases to try.
This is very expensive in AGC mode (lots of candidates that are not real
messages) but relatively cheap otherwise. It yields another 10% messages.
Also factor out some common stats code to avoid lots more copy/paste.
Apparently enabling AGC produces samples with quite different characteristics,
and ends up eating a lot more CPU as the previous heuristics would generate a
lot of false positives. Tweaking the parameters and a bit of optimization
seems to bring this back down to usable levels without losing many potential
messages.
There is a danger in always using relative decoding where possible.
If there is an undetected error in the first pair of messages received,
then global CPR decoding will give a bad position, and subsequent
relative decoding will just walk around near that bad position even
though many error-free pairs of odd/even messages may have been received.
The first pair of position messages also tends to be the most error-prone, as
they are usually received at the extreme edge of receiver range.
(I see this happen at least once a day in practice)
So, instead, prefer to use global decoding when we have sufficiently recent data.
With recent data this should always be as good as relative decoding, and it
avoids getting stuck with bad data for long periods of time. If we don't have
enough recent data for a global solution, fall back to relative decoding.
If a CPR message with an undetected error is received this can produce out-of-range results for latitude.
e.g. even latitude of 78000, odd latitude of 0 produces a latitude index j=35 and rlat0 = 213.
This disables most decoding of the contents of Mode S messages, aircraft tracking, and some output modes that depend on them.
It's intended for edge receivers that just forward to a central hub rather than processing data locally.
Variable j points to the current location in the magnitude vector.
When decoding a message (MODES_PREAMBLE_US+msglen)*2 is added to j.
In the loop head j is increased by 1, so one value was skipped.
Some users have reported issues where the TCP link to dump1090 can be
lost at times of low traffic density - typically in the middle of the
night. One possible reason for this is that some routers drop the link
if there is no traffic for a predetermined period.
To try and resolve this, dump1090 now sends a 'null' packet consisting
of 7 "0x00" bytes approximately once a minute if there is no real
received traffic during this time. This packet should be discarded by
the application receiving the dump1090 because it will have an invalid
checksum, and ICAO address 0x000000 is also invalid. However, this null
packet should be enough to keep routers alive.
The Mutex on the RTL data reader thread does not "force" the data
processing thread to execute. Therefore, if the processor is busy, it is
possible for a second RTL callback to occur before the data from the
first has been processed. This will cause the loss of the first data,
but worse, it will cause a slip in the timestamp. This upsets Beamfinder
and MLAT operation in PlanePlotter.
To solve this, keep a Fifo buffer which is filled by the callback
thread, and emptied by the data processing thread. The fifo is the same
size as the number of buffers requested in the call to
rtlsdr_read_async().
Note - we only put the value of the pointer supplied in the callback
into the fifo. We do not attempt to cache the data in the buffer pointed
to by the pointer. This would require us to memcopy() 2Mbytes per
second, which we don't want to do if we don't have to because it will
only make the processor loading worse. Instead, we assume that the data
in the buffer will remain valid after the callback returns, at least
until it is overwritten by new data.
It is still possible for us to lose data if we can't process it quickly
enough. However, we can now detect this loss of data when the fifo is
almost full, and correct the timestamp for the lost block/blocks.
Don't allow detection of DF-11 SI/II until we have received at least one
DF-11 for the aircraft with an SI/II of zero.
Previous versions would allow an ICAOAddr to be marked as valid if a
DF-11 was received where the crc was less than 80. This is required for
SI/II detection where the SI/II is overlaid on the crc field. However,
this also decreaces the security of the crc. It is possible for a
corrupt message to result in a crc value of between 1 and 79, and this
will lead to an invalid ICAOAddr being marked as received.
To try and prevent this, do not allow detection of DF-11 II/SI fields
until at least one DF-11 crc=0 has been received. Once this happens, we
ca be fairly sure that this aircraft really is within range, and so
II/SI detection can e used.
Updated the way socket handles are used in View1090 to maintain
compatibility between UNIX and Windows.
Added the initial attempt at a Planeplotter uploader
Ok - this is likely to upset some people. Up until now, the vast
majority of the code has been in just one file - dump1090.c. This file
has grown so that it was approaching of 5000 lines long, and it was
becoming unmanagable. So I've split the file into several modules,
hopefully along fairly logical boundaries. The files are :
1) dump1090.c : Basically just the main() entry function, the help
function, the RTL dongle hardware interface, and a few orphan functions
that don't really fit anywhere else.
2) mode_s.c : This contains all the mode S / ADSB decoding functions.
3) mode_ac.c : This contains all the mode A & C decoding functions
4) interactive.c : This contains all the functions to maintain an
internal list of aircraft seen over the last period, and functions to
print them out to the local console.
5) net_io.c : This contains all the network input/output functions
allowing data to be passed in/out to/from other receivers, in formats
such as SBS-1/3, Beast, AVR and JavaScript.
Hopefully this should provide an easier way forward if/when more
functions are added.
